20.11.26

Date added: 20.11.26

Tips for insulating apartments in series 104

Introduction

Apartment block Series 104 are typical Soviet-era panel buildings with known thermal weak points: panel walls, cold joints between panels, uninsulated balconies and older windows. Correct insulation of a Series 104 apartment reduces heating bills, drafts and improves living comfort.

Quick checklist

  • Inspect window openings and panel joints.
  • Start with upgrading or improving windows (PVC with a good profile and insulated glazing).
  • Seal mounting joints and treat end seams correctly.
  • Insulate the balcony/loggia as a separate project.
  • Plan ventilation to avoid excess humidity.

Why Series 104 needs special attention

Series 104 panel houses have factory-made concrete panels and characteristic inter-panel seams. Even with insulated walls, heat is lost through seams and old frames. Insulation should be a combined approach: windows are the most efficient first step.

Windows — where to begin

Choosing a PVC window

  • Profile: 5–7 chamber profiles depending on budget; more chambers improve thermal performance.
  • Glazing: double-glazed units with Low-E coating and argon fill are optimal for Latvian climate.
  • Warm-edge spacer reduces cold bridges around the glass perimeter.
  • Hardware: ventilation functions, durable hinges and secure locks are important.

Installation and sealing

  • Mounting gap: fill gaps with polyurethane foam, then apply sealing tapes — outer tape should be vapor-permeable, inner tape vapor-tight.
  • End seams: seal both outside and inside to protect from moisture and wind.
  • Window reveals: insulated reveals (EPS or mineral wool with vapor barrier) prevent cold bridges.

Balcony and loggia

The balcony in Series 104 is often a major heat leak. Options:

  • Glazing and insulating the balcony with a possible extension of the windowsill creates a thermal buffer.
  • If fully insulated, provide heating or adequate ventilation to avoid condensation.

Panel seams and joints

Inter-panel seams are major cold sources in 104 buildings. Specialized crews use elastic sealants and reinforcing profiles. DIY internal finishing is possible, but seam repair is best left to professionals.

Ventilation and moisture control

Tight windows can raise indoor humidity. Solutions:

  • Install mechanical supply/exhaust ventilation or at least use window micro-ventilation.
  • Use exhaust fans in kitchen and bathroom.
  • Monitor humidity with a hygrometer.

Floors and ceilings

Insulating floors (especially on ground or top floors) requires suitable materials and professional work: insulation under screed, or insulated subfloor solutions. Insulating the ceiling (cold attic) reduces heat loss.

Common mistakes

  • Installing high-performance windows without proper mounting and seam sealing.
  • Ignoring ventilation, leading to mold.
  • Not considering facade specifics when insulating the balcony.

Recommended work sequence

  1. Professional survey and measurements.
  2. Order and install PVC windows with correct thermal specs.
  3. Ensure correct mounting gap treatment and insulated reveals.
  4. Insulate balcony/loggia if planned.
  5. Check and adjust ventilation.

FAQ

Should I replace windows first?

Yes. Windows are one of the most cost-effective improvements to reduce heat loss. However, windows must be installed correctly and seams sealed.

What glazing is recommended for Latvia?

A double-glazed unit with Low-E coating and argon fill is recommended. Consider triple glazing for extremely cold or exposed apartments.

Will insulating the balcony harm ventilation?

It can. Full insulation of a balcony may require added ventilation or regular airing to prevent condensation.

How much does window insulation cost in Series 104?

Costs vary by region and complexity. Typical PVC window replacement with installation can range from budget to mid-range prices. A proper on-site measurement is required for an accurate quote.

Can I seal the mounting gap myself?

Partly yes, but you need to follow the correct layer system (foam, outer tape, inner tape). For complex joints, hire specialists.


Conclusion

Insulating an apartment in Series 104 is a multi-stage process. Begin with windows and correct mounting, then address seams, balconies, floors and ventilation. Proper planning and professional execution maximize the thermal gain and comfort.

DK-Logi blog topics and categories

Useful articles about PVC windows, blinds, and practical advice for your home.

PVC windows

Everything about choosing, installing and maintaining PVC windows.

Blinds and accessories

Tips for choosing blinds, curtains and window accessories.

Tips and answers

Answers to popular questions and practical advice.

GET A FREE WINDOW COST ESTIMATE!

Leave a request, and we will contact you to arrange a free measurement and provide a full cost estimate.

Your name
Your phone number *
Your e-mail
File
Choose file
Comment (e.g., window sizes, quantity, preferred profiles)

2025 © All rights reserved